Optimization of Cutting Parameters in High Speed Turning of Nickel Alloy
DOI:
https://doi.org/10.51983/ajsat-2013.2.2.762Keywords:
ANSYS, Cutter material is cubic boron nitride, Inconel 718, Optimal parameters (cutting speed, feed rate and depth of cut), ProEAbstract
Inconel 718 is one of the important alloys among all the Nickel and Nickel based alloy Inconel 718 has found its niche in many industries, owing to its unique properties. Inconel 718 material is widely used in as aircraft engine parts, steam turbine power plants, space vehicles, But due to peculiar characteristics such as lower thermal conductivity, work hardening, presence of abrasive carbide particles it difficult to machine, Cost effective machining with generation of good surface finish on the Inconel 718 components during turning operation is a challenge to the manufacturing engineers in practice. Considering all the above facts the present work aims to study the influence of different cutting parameters like cutting speed, feed rate and depth of cut of super alloy Inconel 718 and AISI 52100 Steel during high speed turning. Test results were analyzed to determine the better parameters for optimal cutting during high speed machining of Inconel 718 cubic boron nitride tool. A parametric model of cutting tool and work piece is designed using 3D modelling software Pro/Engineer. Analytical investigations are to be made on the model by applying the forces by taking different values of cutting speed, feed rate and depth of cut. Analysis is done in Ansys.
References
Reed R C, The Superalloys, Cambridge University Press, Cambridge, 2006.
Sims C T, Stoloff N S & Hagel W C, Superalloys II, Wiley, New York, 1987.
Radavich J F, Metallurgy and
Applications, edited by Loria E A, TMS, The Minerals, Metals and Materials Society, Pittsburgh, 1989, pp. 229-240. [5] Saunders N, Guo Z, Li X, Miodownik and Schile J P, Superalloys 2004, Edited by Green K A, TMS, The Minerals, Metals and Materials Society, Pittsburgh, 2004, pp. 849-858.
Nalbant M, Altin A and Gökkaya H, Mater Des, 28, (4), 2007, pp. 1334-1338.
Liu G, Int J Mach Mach Mater, 1, (3), 2006.
Rahman M, Seah W K H, Teo T T, J Mater Process Technol, 63 (1-3), 1997, pp. 199-204.
Choudhury I A & El-Baradie M A, J Mater Process Technol, 77 (1-3), 1998, pp. 278-284.
Choudhury I A and El-Baradie M A, Proc Inst Mech Eng, Pt B: J Eng Manuf, 212 (B3), 1998, pp. 195-206.
Graham D, Mod Mach Shop, 75, 2002.
Ezugwu E O, Int J Mach Tools Manuf, 45(12-13), 2005,pp. 1353- 1367.
Schirra J J, in Superalloys 718, 625, 706 and Various Derivatives, TMS, The Minerals, Metals and Materials Society, Pittsburgh,1997, pp. 431-438.
Schulz H, Abele E and Sahm A, Ann CIRP, 50, 45-48.14 Siems S, Dollmeier R & Warnecke G, Trans NAMRI/SME, 28, 2000, pp. 101- 106.
Quan Y M, Wang C Y and He Z W, Adv Mater Manuf Sci Technol Mater Sci Forum, 471-472,2004, pp. 339-343.
Behrens A, Kalisch K and Wulfsberg J P, Possibilities and problems of finite element simulation of high speed cutting mechanics, Proc ASME International Mechanical Engineering, Congress and R&D Exposition, Anaheim, CA, 2004, pp. 1-9.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2013 The Research Publication
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
