Design, Manufacturing and Analysis of Alloy Steel Brake Disc

Authors

  • P. S. Badkar Faculty Of Mechanical Engineering, DKTE’S TEI, Ichalkaranji, Maharashtra, India
  • D. M. Kalai Faculty Of Mechanical Engineering, DKTE’S TEI Ichalkaranji, Maharashtra, India

DOI:

https://doi.org/10.51983/arme-2017.6.1.2420

Keywords:

Disc, brake assembly, wheel rotor, pad, caliper, alloy material, ANSYS, Solid Works, Boundary condition

Abstract

Each single system has been studied and developed in ordered to meet the safety requirement. Instead of having air bag, good suspension systems, good handling and safe cornering, there is one most critical system in the vehicle which is brake system. Without brake system in the vehicle will put a passenger in unsafe position. Therefore, it is must for all vehicles to have proper brake system. In this paper alloy steel disc brake material use for calculating normal force, shear force and piston force And also calculating the brake distance of disc brake. The standard disc brakes two wheelers model using in ANSYS and done the Thermal analysis and Model analysis also calculate the Heat flux and Temperature of disc brake model. This is important to understand action force and friction force on the disc brake new material, how disc brake works more efficiently, which can help to reduce the accident that may happen in each day.

References

Avijit Singh Gangwar, “Design Analysis and Optimization of Disc Brake Assembly of A 4-Wheeler Race Car”, International Journal of Engineering Research and Technology (IJERT)- ISSN:2278-0181, Volume-3, Issue-10, October 2014.

S.R. Abhang , D.P. Bhaskar , “Design and Analysis of Disc Brake” , International Journal of Engineering Trends and Technology (IJETT)- Volume 8 Number 4-Feb 2014.

Rajeshkumar Gangaram Bhandare, Parshuram M. Sonawane, “Preparation of Aluminium Matrix Composite by using Stir Casting Method ”, International Journal of Engineering and Advanced Technology (IJEAT)- ISSN:2249-8958, Volume-3, Issue-2, December 2013.

S. P. Ingale, Prof. A.Z. Patel, Prof. D.D. Date, Prof. A.B.Ghalke, “Advanced Transient Thermal and Structural Analysis of Disc Brake by Ansys Work-bench”, International Research Journal Engineering and Technology (IRJET) – e-ISSN: 2395-0056, p-ISSN:2395-0072.

Pratik P. Chaphale, Dr. S.B. Jaju, “A Review On Thermal and Contact Stress Analysis Of Disc Braking System”, International

Journal of Engineering Research and General Science Volume2, Issue 1, ISSN 2091-2730, January 2014.

Er. N. B. Shinde, Prof. B.R. Borkar, “C.A.D. & F.E.M. ANALYSIS OF DISC BRAKE SYSTEM”, International Journal Of Engineering And Computer Science, ISSN:2319-7242,

Volume 4, Issue 3, March 2015, Page No. 10697-10706

Manjunath T V, Dr Suresh P M, “Structural and Thermal Analysis of Rotor Discof Disc Brake,” International Journal of Innovative Research in Science,Engineering and Technology, ISO 3297: 2007,Vol. 2, Issue 12, December 2013

Sadi, Viktor Malau, M Waziz Wildan, Suyitno, “Optimization of Stir Casting Process Parameters to Minimize the Specific Wear of Al-SiC Composites,” Sadi et al. / International Journal of Engineering and Technology (IJET)

Abhishek Kumar Tiwari, Akhilesh Kumar Tiwari, Pramod Yadav, Harigovind Singh Yadav, Shyam Bihari Lal, “Finite Element Analysis Of Disc Brake By ANSYS Workbench”, IJREAT

Downloads

Published

05-05-2017

How to Cite

Badkar, P. S., & Kalai, D. M. (2017). Design, Manufacturing and Analysis of Alloy Steel Brake Disc. Asian Review of Mechanical Engineering, 6(1), 31–37. https://doi.org/10.51983/arme-2017.6.1.2420

Issue

Vol. 6 No. 1 (2017): January-June 2017

Section

Articles

License

Copyright (c) 2017 The Research Publication

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.