A Review Study of Cold Spray Coating Process
DOI:
https://doi.org/10.51983/arme-2019.8.1.2463Keywords:
Cold Spray, CoatingsAbstract
Cold Spray coatings is a material deposition technique from the broad family of thermal spray coatings with the difference of depositing spray particles at the temperature below melting point as it is a solid state process. The spray particles are impinged on the substrate with supersonic velocities. This paper imparts some light on application of this emerging technique with pros and cons. As this technique come up from last 20 years yet practical area is limited and confined to some research only. As this is a quite beneficial technique and help require from public/private sector to commercialize this technique and hope in coming years it comes up with a good growth in this area.
References
Moridi, S. M. Hassani-Gangaraj, M. Guagliano, “Cold spray coating: review of material systems and future perspectives: Review”, Surface Engineering., Vol. 36, pp. 372-395, 2014.
Harminder Singh, T.S. Sidhu, S.B.S. Kalsi, “Cold spray technology: future of coating deposition processes”, Frattura ed Integrità Strutturale., Vol.22, pp.69-84, 2012.
C.A. Widener, M.J. Carter, O.C. Ozdemir, R.H. Hrabe, B. Hoiland, T.E. Stamey, V.K. Champagne, and T.J. Eden, “Application of High-Pressure Cold Spray for an Internal Bore Repair of a Navy Valve Actuator”, Journal of Thermal Spray., Vol. 25, pp.193-201, 2016.
Christian A. Widener, Ozan C and Michael Carter, “Structural repair using cold spray technology enhanced for sustainability of high value assets”, Procedia Manufacturing., Vol. 21, pp.361-368, 2018.
Shuo Yin, Chaoyue Chen, Xinkun Suo, and Rocco Lupoi, “Cold-Sprayed Metal Coatings with Nanostructure: Review”, Hindawi., Vol.2018 pp.1-19, 2018.
X. T. Luo and C. J. Li, “Thermal stability of microstructure and hardness of cold-sprayed cBN/NiCrAl nanocomposite coating”, Journal of Thermal Spray Technology., Vol. 21, No. 3-4, pp. 578–585, 2012.
X. T. Luo, G. J. Yang, C. J. Li, and K. Kondoh, “High strain rate induced localized amorphization in cubic BN/NiCrAl nanocomposite through high velocity impact”, Scripta Materialia., Vol. 65, No. 7, pp. 581–584, 2011.
H. Assadi, F. G¨artner, T. Stoltenhoff, and H. Kreye, “Bonding mechanism in cold gas spraying”, Acta Materialia., Vol. 51, No. 15, pp. 4379–4394, 2003.
M. R. Rokni, C. A. Widener, and G. A. Crawford, “Microstructural evolution of 7075 Al gas atomized powder and high-pressure cold sprayed deposition”, Surface and Coatings Technology., Vol. 251, pp. 254–263, 2014.
D. Lin, C. Richard Liu, and G. J. Cheng, “Single-layer graphene oxide reinforced metal matrix composites by laser sintering: microstructure and mechanical property enhancement”, Acta Materialia., Vol. 80, pp. 183–193, 2014.
J. Yao, L. Yang, B. Li, and Z. Li, “Beneficial effects of laser irradiation on the deposition process of diamond/Ni60 composite coating with cold spray”, Applied Surface Science., Vol. 330, pp. 300–308, 2015.
G.-J. Yang, P.-H. Gao, C.-X. Li, and C.-J. Li, “Mechanical property and wear performance dependence on processing condition for cold-sprayed WC-(nano WC-Co)”, Applied Surface Science., Vol. 332, pp. 80–88, 2015.
A. F. Richardson, A. Neville, and J. I. B. Wilson, “Developing diamond MMCs to improve durability in aggressive abrasive conditions”, Wear, Vol. 255, No. 1–6, pp. 593–605, 2003.
K. Venkateswarlu, V. Rajinikanth, T. Naveen, D. P. Sinha, Atiquzzaman, and A. K. Ray, “Abrasive wear behavior of thermally sprayed diamond reinforced composite coating deposited with both oxy-acetylene and HVOF techniques”, Wear., Vol. 266, No. 9-10, pp. 995–1002, 2009.
Yingying Wang, Jerome Adrein and Bernard Normand “Porosity Characterization of Cold Sprayed Stainless Steel Coating Using Three-Dimensional X-ray Microtomography”, Coatings., Vol.328 pp.1-8, 2018.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2019 The Research Publication
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
