Mechanical and Biodegradation Behaviour of Jute/ Polylactic Acid Green Composites

Authors

  • Jai Inder Preet Singh Research Scholar, IKG-PTU Kapurthala, Guru Nanak Dev Engineering College, Ludhiana, Punjab, India & Assistant Professor, Lovely Professional University, Phagwara, Punjab, India
  • Sehijpal Singh Principal, Guru Nanak Dev Engineering College, Ludhiana, Punjab, India
  • Vikas Dhawan Director Principal, CGC Landran, Greater Mohali, Punjab, India

DOI:

https://doi.org/10.51983/ajeat-2018.7.2.997

Keywords:

Jute Fibers, Polylactic Acid (PLA), Curing Temperature, Mechanical Characterization, Green Composites, Soil Burial, Bio Degradation

Abstract

Global warming, diminution of fossil fuels, escalating oil price’s are the major reasons which forces the researchers to develop green products for the sustainable development. In this research work, green composites have been developed with jute fibers as reinforcement and poly lactic acid as matrix material using compression moulding technique. All composites were developed with maintaining the reinforcement as 30% fiber volume fraction. The influence of curing temperature with the range of 160°C, 170°C and 180°C was investigated for various mechanical properties of developed composites and degradation behaviour of developed composites were analysed using soil burial test. Results acquired from the tests specify that the tensile and flexural strength decreases with upsurge in curing temperature. Morphology study using scanning electron microscopy is further justified the findings obtained from mechanical tests. Biodegradation study was done on the all the three different composites under the soil burial conditions for 9 months and results indicate that composites developed at 160°C degrade faster as compared to others. This study also gives an optimum curing temperature for the development of jute/PLA composites.

References

P. K. Bajpai, I. Singh, and J. Madaan, "Development and characterization of PLA-based green composites: A review," J. Thermoplast. Compos. Mater., vol. 27, no. 1, pp. 52–81, Mar. 2012.

J. I. P. S. S. Singh and V. Dhawan, "Development and characterization of green composites: A Review," ELK Asia Pacific Journals, 2015.

P. K. Bajpai, I. Singh, and J. Madaan, "Comparative studies of mechanical and morphological properties of polylactic acid and polypropylene based natural fiber composites," J. Reinf. Plast. Compos., vol. 31, no. 24, pp. 1712–1724, Oct. 2012.

A. S. Pannu, S. Singh, and V. Dhawan, "A Review Paper on Biodegradable Composites Made from Banana Fibers," Asian J. Eng. Appl. Technol., vol. 7, no. 2, pp. 7–15, 2018.

V. Dhawan, S. Singh, and I. Singh, "Effect of Natural Fillers on Mechanical Properties of GFRP Composites," J. Compos., vol. 2013, pp. 1–8, 2013.

V. Dhawan, K. Debnath, I. Singh, and S. Singh, "Prediction of Forces during Drilling of Composite Laminates Using Artificial Neural Network: A New Approach," FME Trans. J., vol. 44, no. 1, pp. 36–42, 2016.

S. Jai Inder Preet Singh and V. Dhawan, "Effect of Curing Temperature on Mechanical Properties of Natural Fiber Reinforced Polymer Composites," J. Nat. Fibers, vol. 15, no. 5, pp. 687–696, 2018.

A. Gomes, "Development and effect of alkali treatment on tensile properties of curaua fiber green composites," Compos. Part A Appl. Sci. Manuf., vol. 38, pp. 1811–1820, 2007.

B. K. Goriparthi, K. N. S. Suman, and N. M. Rao, "Effect of fiber surface treatments on mechanical and abrasive wear performance of polylactide/jute composites," Compos. Part A Appl. Sci. Manuf., vol. 43, no. 10, pp. 1800–1808, Oct. 2012.

T. S. Lee et al., "Effect of surface treatment of ramie fiber on the interfacial adhesion of ramie/acetylated epoxidized soybean oil (AESO) green composite," J. Adhes. Sci. Technol., vol. 27, no. 12, pp. 1335–1347, 2013.

J. Inder et al., "Study of Effect of Surface Treatment on Mechanical Properties of Natural Fiber Reinforced Composites," Mater. Today Proc., vol. 4, no. 2, pp. 2793–2799, 2017.

J. F. Martucci and R. A. Ruseckaite, "Biodegradation behavior of three-layer sheets based on gelatin and poly (lactic acid) buried under indoor soil conditions," Polym. Degrad. Stab., vol. 116, pp. 36–44, 2015.

P. Information and P. Details, "Ingeo TM Biopolymer 3052D Technical Data Sheet Injection Molding Process Guide," vol. 001, no. 1, pp. 1–3.

C. Materials, et al., "Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials 1," vol. 1, pp. 1–13, 2013.

ASTM International, "ASTM D 790 – 02 – Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials," vol. 14, pp. 146–154, 2002.

Downloads

Published

02-08-2018

How to Cite

Preet Singh, J. I., Singh, S., & Dhawan, V. (2018). Mechanical and Biodegradation Behaviour of Jute/ Polylactic Acid Green Composites. Asian Journal of Engineering and Applied Technology, 7(2), 52–57. https://doi.org/10.51983/ajeat-2018.7.2.997