Influence of Tillage Depth and Plough Speed on Performance of Primary Tillage Tools

Authors

  • Jagseer Singh Yadavindra College of Engineering, Punjabi University Guru Kashi Campus, Talwandi Sabo, Punjab, India
  • Sukhpal Singh Chatha Yadavindra College of Engineering, Punjabi University Guru Kashi Campus, Talwandi Sabo, Punjab, India
  • Buta Singh Sidhu Maharaja Ranjit Singh Punjab Techanical University, Bathinda, Punjab, India

DOI:

https://doi.org/10.51983/ajeat-2018.7.2.900

Keywords:

Soil Loosening, Tillage Tools, Draft Forces, Chisel Plough, Tillage Depth

Abstract

In India near about 60% population is engaged in agriculture. Soil loosening is a primary method of cultivation before seeding. There are number of tillage tools used for primary cultivation i.e. cultivators, rotary tillers, moldboard plough and chisel plough, rotavators etc. During soil cultivation wear occurs due to interaction of tillage implement and soil particles, which in turn decreases tillage quality and increase draft forces and fuel consumption of tractor. Tool wear reduces farmer’s efficiency, costing millions of dollars per year to Nation’s economy. Knowledge of tillage depth and ploughing speed save the tillage time and improves tractor efficiency. In this study it is attempted to relate the influence of tillage depth and tractor speed on primary tillage tools.

References

United States Department of Agriculture, "India’s Agricultural Exports Climb to Record High," 2014.

I. Hakansson, M. Stenberg, and T. Rydberg, "Long-term experiments with different depths of mouldboard ploughing in Sweden," Soil Till. Res., vol. 46, pp. 209-223, 1998.

S. Ranjbarian, M. Askari, and J. Jannatkhah, "Performance of tractor and tillage implements in clay soil," Journal of the Saudi Society of Agricultural Sciences, vol. 16, pp. 154–162, 2017.

R. L. Kushwaha and C. Linke, "Draft–speed relationship of simple tillage tool at high operating speeds," Soil Till. Res., vol. 39, pp. 61-73, 1996.

W. J. Chancellor and N. C. Thai, "Automatic control of tractor transmission ratio and engine speed," Trans. ASAE, vol. 27, no. 3, pp. 642–646, 1984.

J. D. Grogan, A. Moris, S. W. Searcy, and B. A. Stout, "Microcomputer based tractor performance monitoring and optimization system," J. Agric. Eng. Res., vol. 38, pp. 227–243, 187.

L. A. Smith, "Energy requirements for selected crop production implements," Soil Till. Res., vol. 25, no. 4, pp. 281–299, 1993.

J. A. Michel Jr., K. J. Fornstrom, and J. Borelli, "Energy requirements of the tillage systems for irrigated sugarbeets, dry beans and corn," Trans. ASAE, vol. 28, no. 6, pp. 1731–1735, 1985.

ASAE, "ASAE S313.2: 'Agricultural machinery management data'," ASAE Standards, pp. 657-658, ASAE, St Joseph, MI, 1993.

J. D. Summers, A. Khalilian, and D. G. Batchelder, "Draft relationships for primary tillage in Oklahoma soils," Trans. of the ASAE, vol. 29, no. 1, pp. 37-39, 1986.

A. A. Al-Janobi and A. A. Al-Suhaibani, "Draft of primary tillage implements in sandy loam soil," Trans. of the ASAE, vol. 14, no. 4, pp. 343-348, 1998.

M. Mattetti, M. Varani, G. Molari, and F. Morelli, "Influence of the speed on soil-pressure over a plough," Biosystems Engineering, vol. 156, pp. 136-147, 2017.

T. Taniguchi, J. T. Makanga, K. Ohtoma, and T. Kishimoto, "Draft and soil manipulation by a moldboard plow under different forward speed and body attachments," Transactions of the ASAE, vol. 42, pp. 1517-1521.

S. A. Al-Suhaibani, A. A. Al-Janobi, and Y. N. Al-Majhadi, "Tractors and tillage implements performance," presented at the CSBE/SCGAB 2006 Annual Conference Edmonton Alberta, July 16–19, 2006.

E. Aykas, E. Cakir, and E. Gulsoylu, "The effect of tillage parameters on the performance of heavy duty offset disk harrow," Asian Journal of Plant Sciences, vol. 3, no. 4, pp. 425-428, 2004.

J. V. Stafford, "The Performance of a Rigid Tine in Relation to Soil Properties and Speed," J. Agric. Engng, vol. 24, pp. 41-56, 1979.

J. C. Siemens, J. A. Weber, and T. H. Thornburn, "Mechanics of Soil as Influenced by Model Tillage Tools," Transactions of the ASAE, pp. 1-7, 1965.

S. A. Al-Suhaibani and A. Al-Janobi, "Draught requirements of tillage implements operating on sandy loam soil," Journal of Agricultural Engineering Research, vol. 66, no. 3, pp. 177-182, 1997.

J. Arvidsson, T. Keller, and K. Gustafsson, "Specific draught for mouldboard plough, chisel plough and disc harrow at different water contents," Soil & Tillage Research, vol. 79, pp. 221–231, 2004.

R. L. Raper, "The influence of implement type, tillage depth and tillage timing on residue burial," Transactions of the ASAE, vol. 45, no. 5, pp. 1281–1286, 2002.

G. T. Owen, "Force-Depth Relationships in a Pedogenetically Compacted Clay Loam Soil," Applied Engineering In Agriculture, vol. 5, no. 2, pp. 185-191, 1989.

B. A. Collins and D. B. Fowler, "Effect of soil characteristics, seeding depth, operating speed, and opener design on draft force during direct seeding," Soil & Tillage Research, vol. 39, pp. 199-211, 1996.

R. D. Grisso and M. Yasin, "M. F. Kocher Tillage tool forces operating in silty clay loam," Transactions of the ASAE, vol. 39, pp. 1977–1982, 1996.

S. Rahman and Y. Chen, "Laboratory investigation of cutting forces and soil disturbance resulting from different manure incorporation tools in a loamy sand soil," Soil and Tillage Research, vol. 58, no. 1, pp. 19–29, 2001.

R. J. Godwin, M. J. O’Dogherty, C. Saunders, and A. T. Balafoutis, "A force prediction model for mouldboard ploughs incorporating the effects of soil characteristic properties, plough geometric factors and ploughing speed," Biosystem Engineering, vol. 97, pp. 117–129, 2007.

A. Moeenifar, S. R. Mousavi-Seyedi, and D. Kalantari, "Influence of tillage depth, penetration angle and forward speed on the soil/thin-blade interaction force," Agric Eng Int: CIGR Journal, vol. 16, no. 1, pp. 69-74, 2014.

L. Naderloo, R. Alimadani, A. Akram, P. Javadikia, and H. Z. Khanghah, "Tillage depth and forward speed effects on draft of three primary tillage implements in clay loam soil," Journal of Food, Agriculture and Environment, vol. 76, no. 3, pp. 382–385, 2009.

R. K. Sahu and H. Raheman, "Draught prediction of agricultural implements using reference tillage tools in sandy clay loam soil," Biosyst. Eng., vol. 942, pp. 275–284, 2006.

S. I. Manuwa, "Performance evaluation of tillage tines operating under different depths in a sandy clay loam soil," Soil & Tillage Research, vol. 103, pp. 399–405, 2009.

A. Natsis, G. Papadakis, and J. Pitsilis, "The Influence of Soil Type, Soil Water and Share Sharpness of a Mouldboard Plough on Energy Consumption, Rate of Work and Tillage Quality," Journal of Agriculture Engineering and Research, vol. 72, pp. 171-176, 1999.

C. M. Kichler, J. P. Fulton, R. L. Raper, T. P. McDonald, and W. C. Zech, "Effects of transmission gear selection on tractor and fuel costs during deep tillage operation," Soil & Tillage Research, vol. 113, pp. 105–111, 2011.

A. F. Kheiralla, A. Yahya, M. Zohadie, and W. Ishak, "Modelling of power and energy requirements for tillage implements operating in Serdang sandy clay loam," Soil and Tillage Research, vol. 78, pp. 21–34, 2004.

G. Moitzi, M. Haas, H. Wagentristl, J. Boxberger, and A. Gronauer, "Energy consumption in cultivating and ploughing with traction improvement system and consideration of the rear furrow wheel-load in ploughing," Soil & Tillage Research, vol. 134, pp. 56–60, 2013.

H. Fahollahzadeh, H. Mobli, A. Rajabipour, S. Minaee, A. Jafari, and S. M. H. Tabatabaie, "Average and instantaneous fuel consumption of Iranian conventional tractor with moldboard plow in tillage," ARPN Journal of Engineering and Applied Sciences, vol. 5, no. 2, pp. 30-35, 2010.

Downloads

Published

22-11-2018

How to Cite

Singh, J., Chatha, S. S., & Sidhu, B. S. (2018). Influence of Tillage Depth and Plough Speed on Performance of Primary Tillage Tools. Asian Journal of Engineering and Applied Technology, 7(S2), 138–142. https://doi.org/10.51983/ajeat-2018.7.2.900